DC06 Steel: The Ultra-Low Carbon Deep Drawing Grade of EN 10130

Jun 04, 2025 Leave a message

What DC06 steel is

DC06 (material number 1.0873) is an ultra-low carbon cold-rolled steel for deep drawing, defined in EN 10130. It is one of the two most formable grades of the DC family, together with DC07, and its composition is designed for one purpose: extreme deep drawing without cracking. The maximum carbon content of 0.02% places it well below the 0.25% upper limit normally used to describe low-carbon steel, which is why DC06 is described as ultra-low carbon rather than mild steel.

Chemistry and mechanical properties

Property DC06 value (EN 10130)
Carbon, max 0.02%
Manganese, max 0.30%
Phosphorus, max 0.020%
Sulfur, max 0.020%
Yield strength Rp0.2 (0.7-3.0 mm) 120-180 MPa
Tensile strength Rm 270-350 MPa
Elongation A80, min 38%
Plastic strain ratio r90, min 1.9
Work hardening exponent n90, min 0.21

The very low yield strength and the high r and n values give DC06 excellent resistance to thinning and the ability to deform uniformly, which is exactly what complex deep-drawn parts need.

DC06 vs DC01: what the numbers mean

Property DC01 DC06
Carbon, max 0.12% 0.02%
Yield strength 140-280 MPa 120-180 MPa
Tensile strength 270-410 MPa 270-350 MPa
Elongation A80, min 28% 38%
Typical use Bending, light forming, enclosures Complex deep drawing

DC01 is used for ordinary mechanical parts, simple structural components and general appliance housings where stamping requirements are modest. DC06 costs more and is reserved for parts that DC01 and even DC04 cannot make, such as door inner panels, engine hood inner panels and side panels of cars.

Is DC06 mild steel?

Strictly speaking no. Mild (low-carbon) steel is normally defined with a carbon limit around 0.25%, and DC06 sits at a maximum of 0.02%, in the ultra-low carbon range. The composition is chosen for plasticity, not for strength, so DC06 is the softest and most ductile grade in the EN 10130 family. Its low strength is a feature: the material deforms easily and uniformly in the press instead of tearing.

Equivalents and cross-references

There is no exact equivalent grade for DC06 in other standard systems, because each national standard organizes its deep drawing grades differently. The closest JIS reference is SPCF, the extra deep drawing quality of JIS G 3141, and Chinese 08Al is sometimes used as a substitute with some compromise in elongation. When a project drawing specifies DC06, the safest route is to purchase DC06 to EN 10130 with the required surface quality class rather than substituting an approximate grade.

Where DC06 is used

The main consumer is the automotive industry: complex body panels, door and hood inners, fender inners, oil pans and other parts formed by severe deep drawing. Outside the car, DC06 serves medical devices, precision electronic parts and other applications with strict formability requirements. In each case the material pays for itself by preventing rejected stampings and die modifications.

FAQ

What does the designation DC06 mean?

DC stands for cold rolled flat products for cold forming in the European designation system, and 06 is the grade number, which increases with formability from DC01 up to DC07. DC06 is the special deep drawing grade for the highest forming requirements.

Is DC06 weldable?

Yes, and the very low carbon content gives excellent weldability with resistance welding and conventional arc processes. The low strength does mean the welded joint can be stronger than the base material, which is normal for forming grades.

What is the yield strength of DC06?

For the common thickness range of 0.7-3.0 mm, EN 10130 specifies a yield strength of 120-180 MPa in the annealed condition, the lowest of the deep drawing grades. This low yield strength is what allows ultra-complex deformation.

Can DC06 replace DC04?

Technically yes for easier parts, since DC06 is more formable, but economically it is wasteful: DC06 is more expensive and its lower strength may require thicker gauges. Specify DC04 for normal deep drawing and step up to DC06 only when trials show cracking.

What surface quality classes are available?

EN 10130 defines surface quality classes A, B and C for uncoated cold-rolled product. Automotive exposed parts normally require class A, while hidden parts accept class B. The class must be agreed in the order because it affects price and availability.

Is DC06 the same as SPCE or SPCF?

SPCE is the deep drawing quality of JIS G 3141 and corresponds more closely to DC04 or DC05. SPCF, the extra deep drawing quality, is the closest JIS counterpart to DC06, but the standards differ in detail, so treat it as an approximation, not a full equivalent.