aluminium-zinc is the trade name for steel sheet coated with an aluminium-zinc alloy containing approximately 55% aluminium, 43.4% zinc and 1.6% silicon. The product is defined by ASTM A792/A792M in the United States, by the AZ coating classes of EN 10346 in Europe, and by GB/T 14978 in China. It has a matte, spangle-free appearance and is used for commercial, agricultural and residential roofing and siding, where it combines the corrosion protection of zinc with the barrier durability of aluminium.
What the Coating Is and How It Protects Steel
The AZ coating protects the steel substrate in two complementary ways. The aluminium-rich matrix forms a dense, stable oxide layer that acts as a long-term barrier against oxygen and moisture. The zinc fraction, which forms a network of dendrites through the coating, corrodes preferentially at cut edges and scratches, providing sacrificial protection in the same way as a pure zinc coating. The combination gives a longer barrier life than pure zinc at the same coating mass. Because the alloy density is only about 3.7 g/cm³, roughly half that of zinc, a given coating mass produces nearly twice the coating thickness: AZ150 corresponds to about 20 µm per side, while Z150 zinc is about 10.5 µm per side.
aluminium-zinc vs Galvanized: Key Differences
| Aspect | AZ | Galvanized (+Z) |
|---|---|---|
| Coating composition | 55% Al, 43.4% Zn, 1.6% Si | Pure zinc (min 99% Zn) |
| Barrier life | Longer at equal coating mass | Shorter at equal coating mass |
| Cut-edge protection | Moderate (zinc phase) | Strong (full zinc) |
| Heat reflectivity | Higher, lower emissivity | Lower |
| Appearance | Matte, uniform, no spangle | Spangled or minimised spangle |
| Typical roofing class | AZ150-AZ200 | Z200-Z275 |
Both products are roll-formed into roofing profiles over the same substrate families; the choice depends on environment, budget and appearance.
Performance and Ageing
aluminium-zinc is not rust-proof. Unpainted AZ coating weathers naturally: the surface slowly develops a patchy grey-white patina as the aluminium oxide layer matures. This ageing is cosmetic and does not by itself signal failure. The material performs best when rainwater can wash the surface and when cut edges are cleanly sheared. In humid, coastal or industrial environments, painted aluminium-zinc, or edge protection with more frequent inspection, is recommended, because the zinc phase at the cut edge offers less protection than a pure zinc coating of equivalent mass.
Design and Installation Considerations
Shear edges cleanly; avoid dragging and burrs that expose bare steel.
Avoid direct contact with copper or brass fittings - the galvanic couple accelerates corrosion of the AZ coating.
Avoid long-term contact with acidic run-off, for example from some treated timbers or industrial emissions.
Provide drainage; standing water at laps and edges shortens coating life.
For marine and heavily polluted sites, specify painted AZ with PVDF or HDP systems and sealed or protected edges.
Roofing Applications
Residential roofing and siding panels, in unpainted or painted form.
Agricultural buildings: sheds, barns, livestock housing and storage.
Commercial and industrial roofing and wall cladding, including sandwich panels.
Rain goods: gutters, downspouts and flashings.
Modern and rustic architectural accents where the matte finish is desired.
FAQ
Does aluminium-zinc last longer than galvanized?
In most atmospheric environments, an AZ coating of equal mass outlasts a pure zinc coating because the aluminium phase provides a longer barrier life. The exact ratio depends on the environment, the edge condition and maintenance.
Does aluminium-zinc rust?
Bare aluminium-zinc weathers and may develop surface staining and, at unprotected cut edges over very long exposure, red rust. It is not rust-proof, but in normal service the coating protects the steel for many years.
Can aluminium-zinc be painted?
Yes. Painted AZ products are standard for colour roofing, and bare aluminium-zinc can be painted after proper cleaning and priming.
What is AZ150 or AZ200?
It is the coating class per EN 10346: the total coating mass in grams per square metre over both surfaces measured by the triple-spot method. AZ150 means 150 g/m², about 20 µm per side.
Is aluminium-zinc suitable for coastal areas?
It can be used, but edges are the weak point. Choose painted AZ with protected edges or a higher coating class, and follow the local building code for marine exposure.
Which standards cover aluminium-zinc roofing sheet?
The coating product is covered by ASTM A792/A792M, EN 10346 with AZ classes, and GB/T 14978; the profiled roofing product itself follows the applicable building product standard for the target market.

