DX51D+Z is shorthand for a hot-dip zinc-coated steel flat product that is traded in every market in the world, yet the designation is frequently misread even by experienced buyers. Understanding the name correctly avoids specification errors, because each element of DX51D+Z carries a contractual meaning under EN 10346. This article decodes the designation, explains the four coating systems available in the DX family, and summarises the surface and forming behaviour of the grade.
Decoding the Designation
Under EN 10346, the designation is built in fixed steps. The first D identifies a flat product intended for cold forming. The X states that the chemical composition of the steel is not specified in the standard, the properties are delivered through the combination of base steel and coating, which is typical for commercial forming grades. The number 51 is the serial within the DX series, ranking the grade by forming capability, where 51 is the general level and 52, 53, 54 and higher are progressively better drawing levels. The second D indicates that the metallic coating is applied by the continuous hot-dip process. The suffix +Z then names the coating system, pure zinc in this case. The material number of DX51D+Z is 1.0226 in the European numbering system.
The Four Coating Systems of the DX Series
The suffix after the plus sign selects the coating chemistry. +Z is a pure zinc coating, the standard galvanized product with excellent general corrosion protection and sacrificial behaviour. +ZF is a zinc-iron alloy coating, the galvannealed product, which welds exceptionally well and paints well, used heavily in automotive manufacture. +ZA is a zinc-aluminium coating with roughly 95% zinc and 5% aluminium, offering improved resistance to cut-edge corrosion. +AZ is the aluminium-zinc coating with about 55% aluminium, 43.5% zinc and 1.5% silicon, the aluminium-zinc system, which resists atmospheric corrosion, heat and cut-edge attack better than pure zinc. The coating weight class, such as Z100, Z180 or Z275, is ordered separately and states the total coating mass on both surfaces.
Surface Finish Options
DX51D+Z can be delivered with three spangle appearances. Regular spangle forms the classic crystalline zinc pattern as the coating solidifies and is the economical standard finish. Minimised spangle is produced by controlling the solidification, giving a fine, uniform pattern. Zero spangle, achieved with a suppression treatment and skin pass, gives a smooth, featureless surface that is the preferred base for paint. In addition, the surface can be skin-passed to improve flatness and hardness, and the coil is normally passivated, chromate or chromate-free, and oiled to prevent white rust during storage and transport.
Mechanical and Forming Properties
EN 10346 guarantees DX51D a tensile strength of 270 - 500 MPa and a minimum elongation of 22%, with no yield strength requirement, which is the signature of a forming grade rather than a structural grade. The practical consequence is that DX51D+Z roll-forms, presses and bends cleanly for a wide range of light structures, but it is not the material for deep drawing or for load-bearing design: deep drawn parts move up to DX53D or DX54D, and load-bearing sections move to the S250GD to S550GD structural series. The zinc coating is verified for adhesion by bend tests, and the ductility of the coating is matched to the forming severity through the coating class selection.
Applications of DX51D+Z
The grade is the default material for roofing and cladding profiles, purlins, cable trays, HVAC ducting and casings, lighting and electrical enclosures, fencing, agricultural equipment, and general sheet metal fabrication. Its combination of corrosion resistance, formability and price explains why it is the highest-volume galvanized product in international trade, and why most of the galvanized coil in warehouse stock is DX51D+Z in coating classes Z100 to Z275.
Frequently Asked Questions
What does DX51D+Z stand for?
D marks a flat product for cold forming, X means the steel chemistry is not specified in the standard, 51 is the forming series number, the second D indicates continuous hot-dip coating, and +Z specifies a pure zinc coating. The material number is 1.0226.
Is the last D the galvanizing process code?
Yes, but there are two D letters in the designation. The first D describes the product type, flat steel for cold forming, while the second D, the one after the number 51, identifies the continuous hot-dip coating process. Reading both correctly prevents confusion with cold rolled or electro-coated products.
What is the difference between Z, ZF, ZA and AZ coatings?
Z is pure zinc, ZF is the zinc-iron alloy (galvannealed) coating, ZA is a zinc-aluminium coating of about 95% zinc and 5% aluminium, and AZ is the aluminium-zinc coating of about 55% aluminium. Each trades coating cost against weldability, paintability, heat resistance and cut-edge corrosion performance.
Why is there no yield strength guarantee for DX51D?
EN 10346 defines DX51D by forming behaviour, tensile range 270 - 500 MPa and elongation 22%, rather than by a structural yield value. For guaranteed yield strength, the structural series S220GD to S550GD under the same standard applies.
What does the coating class number mean?
The class, such as Z100 or Z275, is the total mass of the coating in grams per square metre on both surfaces, verified by the triple-spot gravimetric method. Heavier classes give longer corrosion life and are specified for coastal and industrial service.
Can DX51D+Z be deep drawn?
Not reliably. The commercial forming level and the coating ductility limit DX51D+Z to bending, roll forming and shallow forming. For deep drawn parts, specify DX53D+Z or DX54D+Z with a thinner coating class and confirm the drawing performance with the supplier.

