The Function of the Passivation Layer
A galvanized coil has two protective layers. The zinc coating is the main anti-rust layer: it protects the steel substrate sacrificially, corroding in place of the steel. The passivation layer is a very thin, dense film formed on the zinc surface by chemical treatment, either chromate-based or, increasingly, chrome-free. It has three purposes. It prevents white rust, because zinc is a reactive metal that reacts with oxygen and carbon dioxide in humid air to form basic zinc carbonate, the white powder known as white rust; the film isolates the zinc from air and delays this reaction. It improves paint adhesion, providing a better base for subsequent painting or powder coating. And it adds an extra corrosion barrier on top of the zinc.
Short-Term Contact with Clean Fresh Water
Under normal conditions, a high-quality passivation film is dense and firmly bonded to the zinc layer. Brief contact with clean fresh water, such as light rain during handling or a splash in the workshop, does not make the film peel off. Once the water dries, there is essentially no effect. The risk appears only when the film quality is poor, for example when the process was not controlled and the film is too thin or uneven, or when water stays on the surface for a long time. In those cases, water slowly penetrates the film, attacks it locally, and eventually exposes the zinc layer underneath.
Prolonged Immersion and Humid Storage
Prolonged contact with water is a severe test for the passivation layer. Water molecules gradually penetrate the microscopic pores of the film, especially in poorly ventilated conditions such as the inner wraps of a coil or the gap between stacked sheets. Once water reaches the zinc, the zinc corrodes and forms white rust. White rust occupies a larger volume than the zinc it replaces, so it pushes outward from underneath and mechanically damages the overlying film, causing blistering and cracking that looks like the passivation layer has peeled off. The visible sequence is: water ingress, white rust growth, blistering, then flaking of the film. This is why coils stored outdoors or in humid warehouses develop white rust and flaking surfaces, while the coating inside a dry, ventilated warehouse remains intact for long periods.
Chemically Aggressive Water
Chemically treated water is the worst case. Chloride ions, as in brine or seawater, have strong penetrating power and rapidly destroy most passivation films, especially chrome-free systems. Acidic water, such as acid rain, reacts directly with the film and dissolves it. Alkaline water also corrodes the film and the zinc. In all these cases the protection fails much faster than with clean water, and the zinc underneath begins to corrode, typically showing white rust within a short time. Galvanized material should never be specified for continuous contact with aggressive water without an appropriate coating system or additional protection.
Storage and Handling Rules
| Scenario | Risk to passivation layer | Recommended practice |
|---|---|---|
| Brief clean-water contact | Low | Wipe dry; no treatment needed |
| Long immersion in clean water | Medium | Avoid; dry immediately if it occurs |
| Humid storage, condensation | High | Store dry and ventilated, off the floor |
| Seawater or salt-laden air | Very high | Keep away; use marine-grade protection |
| Acid or alkaline water | Very high | Keep away; wash and dry if splashed |
In practice: store galvanized coils in a dry, well-ventilated indoor warehouse. If outdoor storage is unavoidable, raise the coils off the ground and cover them so rainwater cannot pool inside the wraps. Keep finished products away from prolonged immersion and extreme humidity. If the coil will be roll-formed and painted later, protect the passivation layer carefully, because it is essential for paint adhesion and preventing paint peeling.
FAQ
Does water make the passivation layer peel off immediately?
No. A quality film resists brief contact with clean water. Peeling-like damage appears only after prolonged wetness, which causes white rust to grow under the film and push it off.
What actually causes the film to blister and flake?
White rust. Water penetrates to the zinc, the corrosion product expands in volume, and that expansion mechanically blisters and cracks the passivation film, making it look as if it has peeled.
Is the passivation layer resistant to seawater?
No. Chloride ions penetrate most passivation films quickly, especially chrome-free types, so galvanized coils should not be stored or used in salt-laden or seawater conditions without additional protection.
Can white rust be removed and the coil reused?
Light white rust can be wiped or brushed off, and the surface can be treated again, but the zinc consumed is lost. If the zinc coating remains above the required thickness, the coil can be used; otherwise it must be re-galvanized or downgraded.
How should galvanized coils be stored?
Store indoors in a dry, ventilated warehouse, off the floor. If outdoor storage is unavoidable, raise and cover the coils so rainwater cannot accumulate in the wraps, and ventilate to prevent condensation.
Does the passivation layer matter before painting?
Yes. A sound passivation layer improves paint adhesion and prevents paint peeling on galvanized surfaces, so it must be protected until the painting step.

